FH 2763-40 (Inboard clamping beam nylon cutting belt) - A 40 ton, 4 pillar press cutting on a nylon or urethane belt with inboard clamping beam feed and servo drives for accurate feed and excellent material yield. Excellent for cutting multiple material rolls of thin/flimsy material.
FH 3063-70E (Single slide table) - A 70 ton four pillar press with a slide table and 7.1 stroke. Excellent all around diecutter for thin sheet material or thick foam planks. Can cut with the die blade up or down. A Best Buy. Also available with 30 or 100 tons of pressure.
FH 3535-60EM (Die cutting on paper belt system) - A 60 ton, 4 pillar press, bed size of 35 X 35, 7.1 stroke, pneumatic die rails, photocell to activate the 1st cutting stroke, mechanical stops for accurate bottom position, pneumatic die rails and servo drive for accurate feed. Cutting belt can be paper, Mylar, urethane or nylon. This low cost system is particularly well suited for cutting foam planks and rolls. A Best Buy.
FH 3563-100(FoamCutting) - 100 ton, 4 pillar full head press with inboard and outboard conveyors and pinch rolls cutting against a 60RC hardened and ground steel plate with an optional pad and pad shifter. Our most popular and versatile full head press for cutting both roll goods and sheet goods. The German made steel plate has a low friction co-efficiency so most materials will slide across the surface. Add a photocell to activate the first cutting stroke and this is a virtually non-stop automated diecutter with high productivity for sheets or rolls.
FH 5563-100(DoubleAutoSlideTable) - A 100 ton four pillar press with a large bed size of 55 deep by 63 wide is used to cut large parts. Other large bed sizes are available. Having two slide tables allows the machine to be twice as productive as a single slide table for only a small additional cost. Dies can cut with the blade facing up or down and different height dies can be used from each side of the press.
Four Pillar Full Head Hydraulic Presses 25-30 Ton Models - The four pillar full head press is the centerpiece for many automatic cutting systems. It also plays a big role in simple manual operations as well. The full head press in its simple form with a hand slide table is used to cut material from sheets. The dies can be hand placed, mounted to the bridge, or on the table blade up. In the first two cases, the cutting pad is on the slide table of the press. The material to be cut is placed on the cutting pad. The cutting dies are placed on top of the material. The bridge then pushes the dies through the material from the top. In the third case, the die is on the table cutting edge up. This way it does not have to be handled if it is large and heavy. The material to be cut goes on top of the die. The pad is mounted to the bridge. In general one cuts large parts with large dies out of sheets of material. The press should be big enough for the dies and have enough cutting force. Various feed systems can be adapted to the presses as well as pad shifting devices.
Four Pillar Hydraulic Die Cutting Presses 40-200 Ton Models - The four pillar full head press is the centerpiece for many automatic cutting systems. It also plays a big role in simple manual operations as well. The full head press in its simple form with a hand slide table is used to cut material from sheets. The dies can be hand placed, mounted to the bridge, or on the table blade up. In the first two cases, the cutting pad is on the slide table of the press. The material to be cut is placed on the cutting pad. The cutting dies are placed on top of the material. The bridge then pushes the dies through the material from the top. In the third case, the die is on the table cutting edge up. This way it does not have to be handled if it is large and heavy. The material to be cut goes on top of the die. The pad is mounted to the bridge. In general one cuts large parts with large dies out of sheets of material. The press should be big enough for the dies and have enough cutting force. Various feed systems can be adapted to the presses as well as pad shifting devices.
HBC 100 (Cutting against hardened and ground steel plate and or poly pad and pad shifter) - 100 ton, 4 pillar full head press with inboard and outboard conveyors and pinch rolls cutting against a 60RC hardened and ground steel plate with an optional pad and pad shifter. Our most popular and versatile full head press for cutting both roll goods and sheet goods. The German made steel plate has a low friction co-efficiency so most materials will slide across the surface. Add a photocell to activate the first cutting stroke and this is a virtually non-stop automated diecutter with high productivity for sheets or rolls.
USA Series Hydraulic Receding Head Presses - The receding head press is a very versatile die cutting machine. It has the benefits of both the full head press and the traveling head press. The bridge covers the whole cutting area. After a cut it recedes or goes back away from the operator leaving the cutting area open for easy access. With this type of operation one can use small dies or large dies and cut from sheets of rolls of material. The machine can kiss cut or cut to registration depending on what accessories are purchased.
USA Traveling Head - The traveling head press is used to cut man made material that comes on rolls. The width can vary from 60 to over 100. The bed depth generally runs from 20 to 30. Larger machines can be provided to meet customers needs. The depth of the head is usually the same as the bed depth. The width of the head is normally the same as the depth. There are exceptions where it can be wider or narrower. The die should be smaller then the head of the press. The amount of cutting rule should be within the capacity of the machine. The cutting force can be from 20 to 150 tons. Different feed systems are available to assist the operator.
