Cases (Leather and Fancy Goods)

These are machine(s) that can be used for Cases applications in the Leather and Fancy Goods industry. If you would like more information about any of these machine(s), select the machine(s) with the checkboxes on the left, fill out the form below and submit. You will receive a response as soon as possible. Thanks!

		Atom MF Series Oil-Dynamic Clicking Press With Turning Arm - A swing beam hydraulic presses sometimes known as a clicker. It is used to cut leather and man made materials. When choosing this type of machine the things to remember are: A. The material fits on the bed of the press. B. The die fits under the swing beam and does not stick out on either side. C. The amount of cutting rule is limited, so it does not overload the press.
		Atom SE Series Oil-Dynamic Clicking Press With Turning Arm - A swing beam hydraulic presses sometimes known as a clicker. It is used to cut leather and man made materials. When choosing this type of machine the things to remember are: A. The material fits on the bed of the press. B. The die fits under the swing beam and does not stick out on either side. C. The amount of cutting rule is limited, so it does not overload the press.
		FH 3563-60(IncrementalFeed) - A 60-ton four-pillar press with 10 foot long inboard and outboard table stands. The machine can be configured for three different styles of cutting. The first way the machine can cut is by using a long die board with blade up and material on top. The cutting pad is in the head of the press. Also, the machine can have a die mounted in the head and material on a long cutting pad. In a special configuration, the machine can have a long pad, material on top of the pad and loose dies on top of the material. In all three configurations, the material is advanced step by step and cut.
		Four Pillar Full Head Hydraulic Presses 25-30 Ton Models - The four pillar full head press is the centerpiece for many automatic cutting systems. It also plays a big role in simple manual operations as well. The full head press in its simple form with a hand slide table is used to cut material from sheets. The dies can be hand placed, mounted to the bridge, or on the table blade up. In the first two cases, the cutting pad is on the slide table of the press. The material to be cut is placed on the cutting pad. The cutting dies are placed on top of the material. The bridge then pushes the dies through the material from the top. In the third case, the die is on the table cutting edge up. This way it does not have to be handled if it is large and heavy. The material to be cut goes on top of the die. The pad is mounted to the bridge. In general one cuts large parts with large dies out of sheets of material. The press should be big enough for the dies and have enough cutting force. Various feed systems can be adapted to the presses as well as pad shifting devices.
		Four Pillar Hydraulic Die Cutting Presses 40-200 Ton Models - The four pillar full head press is the centerpiece for many automatic cutting systems. It also plays a big role in simple manual operations as well. The full head press in its simple form with a hand slide table is used to cut material from sheets. The dies can be hand placed, mounted to the bridge, or on the table blade up. In the first two cases, the cutting pad is on the slide table of the press. The material to be cut is placed on the cutting pad. The cutting dies are placed on top of the material. The bridge then pushes the dies through the material from the top. In the third case, the die is on the table cutting edge up. This way it does not have to be handled if it is large and heavy. The material to be cut goes on top of the die. The pad is mounted to the bridge. In general one cuts large parts with large dies out of sheets of material. The press should be big enough for the dies and have enough cutting force. Various feed systems can be adapted to the presses as well as pad shifting devices.
		USA Series Hydraulic Receding Head Presses - The receding head press is a very versatile die cutting machine. It has the benefits of both the full head press and the traveling head press. The bridge covers the whole cutting area. After a cut it recedes or goes back away from the operator leaving the cutting area open for easy access. With this type of operation one can use small dies or large dies and cut from sheets of rolls of material. The machine can kiss cut or cut to registration depending on what accessories are purchased.
		USA Traveling Head - The traveling head press is used to cut man made material that comes on rolls. The width can vary from 60” to over 100”. The bed depth generally runs from 20” to 30”. Larger machines can be provided to meet customer’s needs. The depth of the head is usually the same as the bed depth. The width of the head is normally the same as the depth. There are exceptions where it can be wider or narrower. The die should be smaller then the head of the press. The amount of cutting rule should be within the capacity of the machine. The cutting force can be from 20 to 150 tons. Different feed systems are available to assist the operator.

Name:
Email Address:
Company:
Phone Number:
Country:
Project Description: